Soft adhesion to a horizontal flat substrate of micron-sized colloids coated by acontrolled molar fraction f of PLL-g-PNIPAM is tuned and triggered by controllingthe temperature of the sample. This mechanism is possible becausePNIPAM is a thermo-responsive polymer, which undergoes a phase transitionat a LCST (lower critical solution temperature) Tc = 32 +- 1°C. In order tocapture the very final events before the immobilization of colloids the T-rampprotocol is designed: the particles suspension is injected in cell at room temperature,the temperature is increased at a constant rate up to 38°C> Tc, andkept constant until the end of the acquisition. Attraction between beads andthe flat substrate is thereby triggered when crossing the critical temperatureTc. Ascending and descending ramp experiments are performed in order to accessboth adsorption and desorption kinetics. 3-D motion of beads is real-timetracked using slightly defocused microscopy in parallel illumination. We usetrack records to have access to pre-adsorption dffusion coeffcients and to characterizeadsorption and desorption dynamics. Present results corroborate thatadsorption is controlled by PNIPAM doping, and indeed dominated by rollingand memory (aging) effect on the contact domain. On the contrary, the desorption kinetics is independent of doping. Moreover, the sharpness (in T) ofthe PNIPAM transition is quantified in a set of experiments at different rampspeeds. We show that the transition smearing can reach up to +-1°C for higherPNIPAM coverage, while it is not detectable for the lowest ones. The combinationof all these observations paves the way to practical applications. Asan example, we will discuss a soft adhesion-based method to sort and separatecolloids in microfluidic channels.

Secondary flows are ubiquitous in channel flows, where small velocity components perpendicular to the main velocity appear due to the complexity of the channel geometry and/or that of the flow itself such as from inertial or non-Newtonian effects, etc. We investigate here the inertialess secondary flow of viscoelastic fluids in curved microchan-nels of rectangular cross-section and constant but alternating curvature: the so-called "serpentine channel" geometry. Numerical calculations (Poole et al, 2013) have shown that in this geometry, in the absence of elastic instabilities, a steady secondary flow develops that takes the shape of two counter-rotating vortices in the plane of the channel cross-section. We present the first experimental visualization evidence and characterization of these steady secondary flows, using a complementarity of µPIV in the plane of the channel, and L. Ducloué · L. Casanellas · A. Lindner confocal visualisation of dye-stream transport in the cross-sectional plane. We show that the measured streamlines and the relative velocity magnitude of the secondary flows are in qualitative agreement with the numerical results. In addition to our techniques being broadly applicable to the character-isation of three-dimensional flow structures in microchan-nels, our results are important for understanding the onset of instability in serpentine viscoelastic flows.

This paper presents an efficient way to measure the curing kinetics and gel point, αgel, in epoxy resins from one single experiment. The epoxy curing reaction is herein monitored using in situ and time-resolved near-infrared absorption spectroscopy (NIR). The curing profiles over different isothermal conditions are in good agreement with DSC. Furthermore, the increase of the NIR absorption bands of aromatic rings (unreactive throughout curing) probe the cure shrinkage, as more and more aromatic rings are localized within the fixed sample volume. Therefore, the gel point is determined using the onset of the aromatic absorption increase. The results are in good agreement with the theoretical gel point, as well as DMA results. This innovative approach enables gelation measurements on epoxy neat resins and film composites with an easy-to-perform, accurate, robust, and versatile method.

The increase of plastics and microplastics in the environment is a major environmental challenge. Still, little is known about the degradation kinetics of macroplastics into smaller particles, under the joint actions of micro-organisms and physico-chemical factors, like UV or mechanical constraints. In order to gain insight into (bio)-degradation in various media, we perform accelerated erosion experiments by using a well-known enzymatic system. We show that the microstructure of semi-crystalline polymers plays a crucial role in the pattern formation at their surface. For the first time, the release of fragments of micrometric size is evidenced, through a mechanism that does not involve fracture propagation. A geometric erosion model allows a quantitative understanding of erosion rates and surface patterns, and provides a critical heterogeneity size, parting two types of behavior: spherulites either released, or eroded in situ. This new geometric approach could constitute a useful tool to predict the erosion kinetics and micro-particle generation in various media.

Polymerized ionic liquids (PolyILs) are promising materials for applications in electrochemical devices spanning from fuel cells to capacitors and batteries. In principle, PolyILs have a competitive advantage over traditional electrolytes in being single ion conductors and thus enabling a transference number close to unity. Despite this perceived advantage, surprisingly low room temperature ionic conductivities measured in the lab raise an important fundamental question: how does the molecular structure mediate conductivity? In this work, wide-angle X-ray scattering (WAXS), vibrational sum frequency generation (vSFG), and density functional theory (DFT) calculations were used to study the bulk and interfacial structure of PolyILs, while broad band dielectric spectroscopy (BDS) was used to probe corresponding dynamics and conductive properties for a series of the PolyIL samples with tunable chemistries and structures. Our results reveal that the size of the mobile anions has a tremendous impact on chain packing in PolyILs that wasn’t addressed previously. Larger mobile ions tend to create a well-packed structure, while smaller ions frustrate chain packing. The magnitude of these changes and level of structural heterogeneity are shown to depend on the chemical functionality and flexibility of studied PolyILs. Furthermore, these experimental and computational results provide new insight into the correlation between conductivity and structure in PolyILs, suggesting that structural heterogeneity helps to reduce the activation energy for ionic conductivity in the glassy state.