The so-called buffer layer (BL) is a carbon rich reconstructed layer formed during SiC (0001) sublimation.The covalent bonds between some carbon atoms in this layer and underlying silicon atoms makes itdifferent from epitaxial graphene. We report a systematical and statistical investigation of the BLsignature and its coupling with epitaxial graphene by Raman spectroscopy. Three different BLs arestudied: bare buffer layer obtained by direct growth (BL0), interfacial buffer layer between graphene andSiC (c-BL1) and the interfacial buffer layer without graphene above (u-BL1). To obtain the latter, wedevelop a mechanical exfoliation of graphene by removing an epoxy-based resin or nickel layer. The BLsare ordered-like on the whole BL growth temperature range. BL0 Raman signature may vary from sampleto sample but forms patches on the same terrace. u-BL1 share similar properties with BL0, albeit withmore variability. These BLs have a strikingly larger overall intensity than BL with graphene on top. Thesignal high frequency side onset upshifts upon graphene coverage, unexplainable by a simple straineffect. Two fine peaks (1235, 1360 cm1), present for epitaxial monolayer and absent for BL and transferred graphene. These findings point to a coupling between graphene and BL.

The antagonistic effect of processing and thermal annealing on both the filler structure and the polymer matrix is explored in polymer nanocomposites based on natural rubber with precipitated silica incorporated by coagulation from aqueous suspension followed by roll-milling. Their structure and linear and non-linear rheology have been studied, with a particular emphasis on the effect of high temperature thermal treatment and the number of milling passes. Small-angle X-ray scattering intensities show that the silica is organized in small, unbreakable aggregates containing ca. 50 primary nanoparticles, which are reorganized on a larger scale in filler networks percolating at the highest silica contents. As expected, the filler network structure is found to be sensitive to milling, more milling inducing rupture, as evidenced by the decreasing Payne effect. After thermal treatment, the nanocomposite structure is found to be rejuvenated, erasing the effect of the previous milling on the low-strain modulus. In parallel, the dynamics of the samples described by the rheology or the calorimetric glass-transition temperature remain unchanged, whereas the natural latex polymer network structure is modified by milling towards a more fluid-like rheology, and cannot be recovered.

Nuclear magnetic resonance imaging (MRI) has became an unavoidable medical tool in spite of its poor sensitivity. This fact motivates the efforts to enhance the nuclear magnetic resonance (NMR) probe performance. Thus, the nuclear spin excitation and detection, classically performed using radio-frequency coils, are required to be highly sensitive and homogeneous. The space harmonics suppression (SHS) method, already demonstrated to construct coil producing homogenous static magnetic field, is used in this work to design radio-frequency coils. The SHS method is used to determine the distribution of the electrical conductive wires which are organized in a saddle-coil-like configuration. The theoretical study of these SHS coils allows one to expect an enhancement of the signal-to-noise ratio with respect to saddle coil. Coils prototypes were constructed and tested to measure 1H NMR signal at a low magnetic field (8 mT) and perform MRI acquired at a high magnetic field (3 T). The signal-to-noise ratios of these SHS coils are compared to the one of saddle coil and birdcage (in the 3 T case) of the same size under the same pulse sequence conditions demonstrating the performance enhancement allowed by the SHS coils.

High temperature, high pressure conditions were used to insert liquid bismuth in 4-6 nm diameter amorphous silica nanotubes. A combination of transmission electron microscopy and neutron powder diffrac-tion indicate that the final composite consists in 5-6 nm semi-conducting Bi nanowires confined in insulating mesoporous -quartz. Such a nanostructured material could be of considerable interest for thermo-electric applications. HIGHLIGHTS:  Bismuth was inserted into 4-6 nm silica nanotubes under high-pressure, high-temperature conditions  The host amorphous nanotubes crystallize in the form of -quartz  The obtained nanocomposite consists of 5-6 nm Bi nanowires imbedded in mesoporous -quartz  The formation of Bi nanowires modifies their physical properties compared to bulk Bi