Abstract The topology of amorphous materials can be affected by mechanical forces during compression or milling, which can induce material densification. Here, we show that densified amorphous silica (SiO 2 ) fabricated by cold compression of siliceous zeolite (SZ) is permanently densified, unlike densified glassy SiO 2 (GS) fabricated by cold compression although the X-ray diffraction data and density of the former are identical to those of the latter. Moreover, the topology of the densified amorphous SiO 2 fabricated from SZ retains that of crystalline SZ, whereas the densified GS relaxes to pristine GS after thermal annealing. These results indicate that it is possible to design new functional amorphous materials by tuning the topology of the initial zeolitic crystalline phases.

The negative thermal expansion material potassium cadmium dicyanoargentate, KCd[Ag(CN) 2 ] 3 , is studied at high pressure using a combination of X-ray single-crystal diffraction, X-ray powder diffraction, infrared and Raman spectroscopy, and density functional theory calculations. In common with the isostructural manganese analogue, KMn[Ag(CN) 2 ] 3 , this material is shown to exhibit very strong negative linear compressibility (NLC) in the crystallographic c direction due to structure hinging. We find increased structural flexibility results in enhanced NLC and NTE properties, but this also leads to two pressure-induced phase transitionsto very large unit cells involving octahedral tilting and shearing of the structurebelow 2 GPa. The presence of potassium cations has an important effect on the mechanical and thermodynamic properties of this family, while the chemical versatility demonstrated here is of considerable interest to tune unusual mechanical properties for application. ■ INTRODUCTION Materials where external stimuli induces an anomalous response, such as expansion upon cooling (negative thermal expansion, NTE 1−3) or on application of hydrostatic pressure (negative linear compressibility, NLC 4,5), have recently received considerable attention. These materials that "break the rules"as a result of specific, and therefore rare, elastic anomalies 6−8 are curious from a fundamental point of view but might also be revolutionary for a range of technologies including interferometric pressure sensors, pressure-controlled or pressure-sensitive electronic devices, and smart actua-tion. 2,4,9−11 The ability to design materials with unusual properties is therefore a key focus of the field: can we understand these elastic anomalies so that we can tune the magnitude and/or range of negative responses? Negative thermal expansion may occur in one, two, or all principal directions without violating thermodynamics. 12,13 Thus, for example, the volume coefficient of thermal expansion (CTE), () V V V T p 1 α = ∂ ∂ , takes large negative values in zirconium tungstate ZrW 2 O 8 and zinc(II) cyanide Zn(CN) 2 over large temperature ranges. 14 Under hydrostatic pressure, however, volume must always reduce and so the volume compressibility (() K V V V p T 1 = − ∂ ∂ , conventionally formulated as the bulk modulus, B = (K V) −1), must be definite and positive. 15 Expansion under pressure can occur in one or two directions, as long as this is coupled to volume reduction. 5,12,16 Therefore, negative linear compressibility (NLC)the expansion in one principal direction of a material under hydrostatic pressureis conceptually and empirically related to linear-NTE. In both cases, anomalous response relies on mechanical anisotropy. The so-called "wine-rack" model is often invoked where mechanical hinging allows linear expansion coupled to volume reduction on increasing pressure or decreasing temperature. 5,8 Attention in this field has focused on a class of materials known as coordination polymers (CPs), in particular due to the very large magnitude of responses found in comparison to conventional oxide-based materials. 7 Examples that show large NTE and NLC include cyanide frameworks such as Ag 3 [Co-(CN) 6 ] (refs 17 and 18), KMn[Ag(CN) 2 ] 3 (refs 19 and 20), Zn[Au(CN) 2 ] 2 (refs 21 and 22), and metal−organic frameworks 23 (MOFs) such as MIL-53 (ref 24), UTSA-16 (ref 25), ZAG-4 (ref 26), and [NH 4 ][Zn(HCOO) 3 ] (ref 27). In many cases, mechanical response can be predicted in these systems by considering the framework as a set of rigid connectors and hinges, sodepending on geometry and topologyNTE or

In this paper, we present the different characterization techniques used to measure the mechanical properties of silica aerogels. The mechanical behaviour of aerogels is generally described in terms of elastic and fragile materials (such as glasses or ceramics) but also in terms of plastic media in compression testing. Because of these very different mechanical behaviors, several types of characterization techniques are proposed in the literature. We first describe the dynamic characterization techniques such as ultrasounds, Brillouin scattering, dynamic mechanical analysis (DMA) to measure the elastic properties: Young's modulus (E) , shear modulus (G), poisson ratio (υ) but also attenuation and internal friction. Thanks to "static" techniques such as three-point bending, uniaxial compression, compression we also access to the elastic modulus (E) and to the rupture strength (σ). The experimental results show that the value of the elastic and fracture moduli measured is several orders of magnitude lower than that of a material without porosity. With regard to the brittleness characteristics, Weibull's analysis is used to show the statistical nature of the fracture resistance. We also present the SENB (single edge notched beam technique) technique to characterize toughness (K1C) and the stress corrosion mechanisms, which are studied in ambient conditions and temperature by the double-cleavage drilled compression experiment (DCDC). In the last part of the paper, we show how, during the isostatic compression test, aerogels behave like plastic materials.The data allow calculating the bulk modulus (K), the amplitude of the plastic deformation and the yield strength (σel), which is the boundary between the elastic and plastic domains. These different techniques allow understanding which parameters influence the overall mechanical behavior of aerogels, such as pore volume, but also pore size, internal connectivity and silanol bounds content. It is shown that pore size plays a very important role; pores can be considered as flaws in the terms of fracture mechanics.

The Raman modes of α-quartz-type boron phosphate were found to be extremely stable in frequency over a large temperature range from 300–1000 K. In order to determine the origin of this behavior, the material was also studied at high pressure up to 6 GPa. Upon compression, a classical behavior was observed with mode Grüneisen parameters ranging from −0.08(2) to 3.0(1). The present results indicate that the high temperature behavior in this material is an example of an unusual compensation effect between phonon–phonon interactions and implicit contributions due to thermal expansion. Phonon stability is of utmost importance for materials properties that are dependent on it such as dielectric and piezoelectric properties, for example. Boron phosphate belongs to the important class of α-quartz-type piezoelectric materials for which temperature stability is of primordial importance for resonator and sensor applications.

alpha-Quartz-type gallium phosphate and representative compositions in the AlPO4-GaPO4 solid solution were studied by x-ray powder diffraction and absorption spectroscopy, Raman scattering, and by first-principles calculations up to pressures of close to 30 GPa. A phase transition to a metastable orthorhombic high-pressure phase along with some of the stable orthorhombic Cmcm CrVO4-type material is found to occur beginning at 9 GPa at 320 degrees C in GaPO4. In the case of the AlPO4-GaPO4 solid solution at room temperature, only the metastable orthorhombic phase was obtained above 10 GPa. The possible crystal structures of the high-pressure forms of GaPO4 were predicted from first-principles calculations and the evolutionary algorithm USPEX. A predicted orthorhombic structure with a Pmn2(1) space group with the gallium in sixfold and phosphorus in fourfold coordination was found to be in the best agreement with the combined experimental data from x-ray diffraction and absorption and Raman spectroscopy. This method is found to very powerful to better understand competition between different phase transition pathways at high pressure.

AlPO4-17, known as the oxide with the highest negative thermal expansion (NTE), was studied under high pressure by angle-dispersive X-ray diffraction (XRD), mid- and far-infrared (IR) spectroscopy. Upon increasing pressure, the closure of the (P–O–Al) angle destabilizes the porous AlPO4-17 structure, which drives the amorphization process. On the basis of the decrease in intensity of the XRD lines and broadening of the IR modes, the material was found to begin to amorphize near 1 GPa. XRD, mid- and far-IR analysis evidenced pressure-induced framework softening and complete irreversible amorphization near 2.5 GPa corresponding to the collapse of the pores. The bulk modulus and its first pressure derivative (B0 = 31.2(5) GPa and B′0 = −10.1(3)) at ambient temperature were determined by fitting a third order Birch–Murnaghan equation of state (EOS) to the pressure–volume data. The material is extremely compressible and exhibits an elastic instability. Anomalous (negative) values of B′0 are very rare and have been observed previously for cyanides and metal–organic frameworks. Such an instability appears to be characteristic of materials, which exhibit strong NTE behavior and indicates a link between NTE and anomalous compressibility behavior. Mid-IR, far-IR, nuclear magnetic resonance, and pair distribution function analysis of the new amorphous form allow an amorphization mechanism to be proposed corresponding to a collapse of the structure around its pores retaining the columns built up of cancrinite cages and hexagonal prisms, based on alternating AlO4 and PO4 tetrahedra. An increase in coordination number of 10% of the Al atoms was observed. The pressure-induced amorphization in the strong NTE material AlPO4-17 opens the door to the development of new technological applications as crystal–amorphous nanocomposites with zero or specifically selected thermal expansion coefficients.