It has recently been shown that Terahertz sensors can effectively detect the spin resonances of Dirac fermions in graphene. The associated photovoltaic measurement technique allows for the investigation of the intrinsic spin-orbit coupling in graphene as well as its topological properties from microwave to Terahertz frequencies. In this work, using graphene/MoS₂-based Field-Effect Transistors, we observed a magnetic resonance photovoltage signal in the Gigahertz range that is independent on the gate bias. The dispersion of the associated spin-flip transitions remains intriguingly unaffected by the MoS₂ layer. In parallel, the spin-related signal consistently appears as a drop in photovoltage, regardless of the signal's polarity or origin, whether it is due to plasma wave rectification or thermoelectric effects. This behavior is interpreted as a decrease in the system's spin polarization due to spin-dependent recombination or scattering of photocarriers. Understanding the various photovoltaic signals in highly sensitive Gigahertz/Terahertz sensors paves the way for exploring spin-dependent mechanisms in two-dimensional quantum materials, influenced by proximity effects such as spin-orbit coupling, topology, and magnetism.

Hydrogen is considered a promising alternative to conventional fossil fuels, as it can be easily produced from renewable energy sources. While electrocatalytic water splitting can achieve near-unity faradaic efficiency in producing hydrogen from water, the widespread implementation of large-scale water electrolysis is hindered by reliance on costly platinum group metal-based electrocatalysts. Here, we report on the rational design of Molybdenum-containing SiCN composites (Mo–SiCN) through an active-filler controlled pyrolysis (AFCOP) strategy. Our investigation into the composite's microstructural evolution revealed the formation of a Mo4.8Si3C0.6 Nowotny phase at a relatively low temperature of 1000 °C. After optimization, the resulting catalyst demonstrated a Tafel slope below 95 mV dec−1 and an overpotential near 575 mV at a normalized current density of 1 mA μF−1. As a proof of concept, the AFCOP strategy was employed to engineer a crack-free Mo–SiCN micropattern, enabling the miniaturization of a Pt-free electrochemical water splitting (EWS) reactor. Produced via soft lithography, the Mo–SiCN pattern exhibits feature sizes ranging from 10 to 200 μm, with near-net-shape replication and a Young's modulus of ≈60 GPa.

Inter-individual variability in muscle responses to mechanical stress during exercise is poorly understood. Therefore, new cell culture scaffolds are needed to gain deeper insights into the cellular mechanisms underlying the influence of mechanical stress on human myogenic progenitor cells behavior. To this end, we propose the first in vitro model involving uniaxial mechanical stress applied to aligned human primary muscle-derived cells, employing a biocompatible organic–inorganic photostructurable hybrid material (OIPHM) covalently attached to a stretchable PDMS support. Using a laser printing technique with an additive photolithographic process, we optimally micropatterned the PDMS support to create longitudinal microgrooves, achieving well-aligned muscle fibers without significantly affecting their diameter. This support was biofunctionalized with peptide sequences from the ECM, which interact with cellular adhesion receptors and prevent myotube detachment induced by stretching. X-ray photoelectron spectroscopy (XPS) of biofunctionalized PDMS with RGD-derived peptide deposition revealed a significant increase in nitrogen compared to silicon, associated with the presence of a 380 nm thick layer measured by atomic force microscopy (AFM). Upon cell culture, we observed that functionalization with an RGD peptide had a beneficial impact on cell fusion rate and myotube area compared to bare PDMS. At the initiation of the stretching protocol, we observed a three-fold rapid and transient increase in RNA expression for the mechanosensitive ion channel protein piezo and a decrease in the ratio of nuclei expressing myogenin relative to the total nuclei count (43 ± 16% vs. 6 ± 6%, p < 0.01). Compared to day 0 of differentiation, stretching the myotubes induced MHC and Titin colocalization (0.66 ± 0.13 vs. 0.93 ± 0.05, p < 0.01), favoring sarcomere organization and maturation. In this study, we propose and validate an optimized protocol for culturing human primary muscle-derived cells, allowing standardized uniaxial mechanical stress with a biocompatible OIPHM covalently linked to PDMS biofunctionalized with an ECM-derived peptide, to better characterize the behavior of myogenic progenitor cells under mechanical stress in future studies.