The challenge is to achieve high specificity in molecular sensing by proper functionalization of micro/nano-structured semiconductors by peptides that reveal specific recognition for these structures. Here we report on surface modification of the InP semiconductors by adhesion peptides produced by the phage display technique. An M13 bacteriophage library has been used to screen 1010 different peptides against the InP(001) and the InP(111) surfaces to finally isolate specific peptides for each orientation of the InP. MALDI-TOF/TOF mass spectrometry has been employed to study real affinity of the peptide towards the InP surfaces. The peptides serve for controlled placement of biotin onto InP to bind then streptavidin. Our Atomic Force Microscopy study revealed a total surface coverage of molecules when the InP surface was functionalized by its specific biotinylated peptide (YAIKGPSHFRPS). Finally, fluorescence microscopy has been employed to demonstrate the preferential attachment of the peptide onto a micro-patterned InP surface. Use of substrate specific peptides could present an alternative solution for the problems encountered in the actually existing sensing methods and molecular self-assembly due to the unwanted unspecific interactions.

Infiltration of biomacromolecules into porous silicon photonic architectures results in biofunctionalized structures with unique properties. Characterization of their optical response and performance optimization in biomacromolecular detection and biophotonic application require a combination of optical and structural studies. Nonlinear optical microscopy is applied to study porous silicon microcavities with and without infiltrated glucose oxidase. The infiltrated protein acts as an internal two-photon-excited fluorescence emitter and second harmonic generator, enabling the in-depth visualization of the porous structure. Enhanced second harmonic generation and fluorescence emission by the porous silicon structure is experimentally associated with the defect layer.

Nanobiotechnology aims to exploit biomolecular recognition and self-assembly capabilities for integrating advanced materials into medicine and biology. However frequent problems are encountered at the interface of substrate-biological molecule, as the direct physical adsorption of biological molecules is dependent of unpredictable non-specific interactions with the surface, often causing their denaturation. Therefore, a proper functionalization of the substrate should avoid a loss of biological activity. In this work we address the functionalization of the semiconductor GaN (0001) for biosensing applications. The basic interest of using III-V class semiconductors is their good light emitting properties and a fair chemical stability that allows various applications of these materials. The technology chosen to elaborate GaN-specific peptides is the combinatorial phage-display method, a biological screening procedure based on affinity selection. An M13 bacteriophage library has been used to screen 10(10) different peptides against the GaN (0001) surface to finally isolate one specific peptide. The preferential attachment of the biotinylated selected peptide onto the GaN (0001), in close proximity to a surface of different chemical and structural composition has been demonstrated by fluorescence microscopy. Further physicochemical studies have been initiated to evaluate the semiconductor-peptide interface and understand the details in the specific recognition of peptides for semiconductor substrates. Fourier Transform Infrared spectroscopy in Attenuated Total Reflection mode (FTIR-ATR) has been employed to prove the presence of peptides on the surface. Our Atomic Force Microscopy (AFM) studies on the morphology of the GaN surface after functionalization revealed a total surface coverage by a very thin, homogeneous peptide layer. Due to its good biocompatibility, functionalized GaN devices might evolve in a new class of implantable biosensors for medical applications.

PSi microcavity (PSiMc) is characterized by a narrow resonance peak in the optical spectrum that is very sensitive to small changes in the refractive index. We report that the resonant optical cavities of PSi structures can be used to enhance the detection of labeled fluorescent biomolecules. Various PSi configurations were tested in order to compare the optical response of the PSi devices to the capture of organic molecules. Morphological and topographical analyses were performed on PSiMc using Atomic Force (AFM) and Scanning Electron (SEM) microscopies. The heterogeneity in pores lengths resulting from etching process assures a better penetration of larger molecules into the pores and sensor sensitivity depends on the pore size. Molecular detection is monitored by the successive red shifts in the reflectance spectra after the stabilization of PSiMc with 3-aminopropyltriethoxysilane (APTES). The glucose oxidase was crosslinked into the PSiMc structures following a silane-glutaraldehyde (GTA) chemistry.

Bacteriorhodopsin (BR) is a robust trans-membrane protein that functions as a light-driven proton pump, thus is an excellent candidate for biophotonics applications. For the development of new optical devices, the buildup of stable BR matrices has to be optimised. In this work, we present a multi-technique approach: the combination of optical waveguide lightmode spectroscopy (OWLS), atomic force microscopy (AFM) and multi-photon microscopy (MPM) aiming to analyze the optical and physico-chemical properties of BR embedded in polyelectrolyte multilayers (PEM) in its membrane bound form (purple membrane, PM), as well as solubilized BR immobilized within a photonic structure built of porous silicon (PSi). OWLS measurements revealed the possibility of incorporation of PM-BR layers into PE-multilayers. The calculated thickness and refractive index of the adsorbed layers demonstrate the successful adsorption of PM on top of the positively or negatively charged PE layers. Morphological studies by AFM proved a complete coverage of the positively charged PE layer with PM patches. As for the other model system, photonic responses of BR, after being immobilized within PSi substrates, have been evaluated using multi-photon microscopy. Fluorescence emission and second harmonic generation (SHG) of the BR-PSi system were observed at some particular pores of PSi and subsequent enhancement of the signal arising from the BR adsorbed within the pores was detected. Our results constitute the first steps of two interesting and innovative biomimetic approaches for the future design and development of BR based integrated optical devices.