The functionalization of carbon nanotubes by polymers necessitates two steps, first their modification by oxidizing them or by covalently attaching small compounds to them, then the growth of the polymer chains from these anchors or their grafting onto them. In order to better control the process and the rate of functionalization, we develop polymers able to covalently react with the carbon nanotubes by their side chains in one step. We describe the synthesis of a copolymer of dodecylthiophene and its analogue bearing an aniline group at the end of the dodecyl side chain. This copolymer can functionalize single-walled carbon nanotubes (SWNTs) non-covalently and disperse more SWNTs than its hexyl analogues. UV-Vis and fluorescence spectroscopies show that in these non-covalent hybrids, the polymer forms p-stacked aggregates on the SWNTs. The non-covalent hybrids can be transformed into covalent ones by diazonium coupling. In these covalent hybrids the polymer is no longer p-stacked. According to Raman spectroscopy, the conformation of the poly(3-hexylthiophene) backbone is more ordered in the non-covalent hybrids than in the covalent ones.

In the design of medium and low voltage equipment such as cable accessories, generator, motor end windings or bushings, issues with electrical field enhancement occur at interfaces between insulators and conductors, resulting in accelerated material ageing. The purpose of this paper is to present a novel dielectric composite material which has the properties to mitigate this local amplification. It is a functional dielectric which resistivity decreases by several orders with electric field from 10(14) to 10(9) ohm m up to 1 kV mm(-1) while the dielectric constant decreases from 15 to 12 in the 10(-2)-10(6) Hz range. This novel material is made with graphite nanoplatelets. It may be used as a resistive or capacitive field grading material in electrical applications.

Understanding the complex structure of polymer blends filled with nanoparticles (NPs) is the key to designing their macroscopic properties. Here, the spatial distribution of hydrogenated (H) and deuterated (D) polymer chains asymmetric in mass is studied by small-angle neutron scattering. Depending on the chain mass, a qualitatively new large-scale organization of poly(vinyl acetate) chains beyond the random-phase approximation is evidenced in nanocomposites with attractive polymersilica interactions. The silica is found to systematically induce bulk segregation. Only with long H-chains, a strong scattering signature is observed in the q-range of the NP size: it is the sign of interfacial isotopic enrichment, i.e., of contrasted polymer shells close to the NP surface. A quantitative model describing both the bulk segregation and the interfacial gradient (over ca. 10-20 nm depending on the NP size) is developed, showing that both are of comparable strength. In all cases, NP surfaces trap the polymer blend in a non-equilibrium state, with preferential adsorption around NPs only if chain length and isotopic preference towards the surface combine their entropic and enthalpic driving forces. This structural evidence for interfacial polymer gradients will open the road to quantitative understanding of the dynamics of many-chain nanocomposite systems.

The polarized fluorescence emission of organic fluorophores has been extensively studied in photonics and is increasingly exploited in single molecule scale bio-imaging. Expanding the polarization properties of compact molecular assemblies is, however, extremely challenging due to depolarization and quenching effects associated with the self-aggregation of molecules into the sub-nanometer scale. Here we demonstrate that Boron Nitride Nanotubes (BNNTs) can act as a 1D host-template for the alignment of encapsulated a-sexithiophene (6T) inside BNNTs, leading to an optically active 6T@BNNT nanohybrid. We show that the fluorescence from the nanohybrid is strongly polarized with extinction ratios as high as 700 at room temperature. A statistical analysis of the 6T orientation inside BNNTs with inner diameter up to 1.5 nm shows that at least 80% of the encapsulated 6Ts exhibit a maximum deviation angle of less than 10{\deg} with respect to the BNNT axis. Despite a competition between molecule-molecule and molecule-BNNT adsorption in larger BNNTs, our results also show that more than 80% of the molecules display a preferential orientation along the BNNT axis with a deviation angle below 45{\deg}.

Nanoporous carbons remain the most promising candidates for effective hydrogen storage by physisorption in currently foreseen hydrogen-based scenarios of the world’s energy future. An optimal sorbent meeting the current technological requirement has not been developed yet. Here we first review the storage limitations of currently available nanoporous carbons, then we discuss possible ways to improve their storage performance. We focus on two fundamental parameters determining the storage (the surface accessible for adsorption and hydrogen adsorption energy). We define numerically the values nanoporous carbons have to show to satisfy mobile application requirements at pressures lower than 120 bar. Possible necessary modifications of the topology and chemical compositions of carbon nanostructures are proposed and discussed. We indicate that pore wall fragmentation (nano-size graphene scaffolds) is a partial solution only, and chemical modifications of the carbon pore walls are required. The positive effects (and their limits) of the carbon substitutions by B and Be atoms are described. The experimental ‘proof of concept’ of the proposed strategies is also presented. We show that boron substituted nanoporous carbons prepared by a simple arc-discharge technique show a hydrogen adsorption energy twice as high as their pure carbon analogs. These preliminary results justify the continuation of the joint experimental and numerical research effort in this field.

The field of ion transport through carbon nanotubes (CNTs) is marked by a large variability of the ionic conductance values reported by different groups. There is also a large uncertainty concerning the relative contributions of channel and access resistances in the experimentally measured currents, both depending on experimental parameters (nanotube length and diameter). In this perspective article, we discuss the ionic conductance values reported so far in the case of 2 individual CNTs and compare them with standard nano-fluidic models considering both the access and channel resistances. With a view toward guiding experimentalists, we thus show in which conditions the access or the channel resistance can predominate in CNTs. We explain in particular that it is not justified to use phenomenological models neglecting the channel resistance in the case of micrometer-long CNTs. This comparison reveals that most experimental conductance values can be explained in the framework of current nanofluidic models by considering experimental variations of slip length and surface charge density and that just a few extraordinarily high values cannot be accounted for even using extreme parameter values. Finally, we discuss how to complete existing models and how to improve the statistical reliability of experimental data in the field.