• Sciences de l'ingénieur/Acoustique
  
• Sciences de l'ingénieur/Matériaux
  
• Sciences de l'ingénieur
  
• Chimie/Matériaux
  
• Physique/Matière Condensée/Science des matériaux
  
• Sciences de l'ingénieur/Mécanique
  
• Sciences de l'ingénieur/Mécanique/Mécanique des matériaux
  
• Chimie
  
• Physique/Matière Condensée/Systèmes désordonnés et réseaux de neurones
  
• Physique/Matière Condensée/Mécanique statistique
  
• Physique/Matière Condensée/Matière Molle
  

In this paper, we present the different characterization techniques used to measure the mechanical properties of silica aerogels. The mechanical behaviour of aerogels is generally described in terms of elastic and fragile materials (such as glasses or ceramics) but also in terms of plastic media in compression testing. Because of these very different mechanical behaviors, several types of characterization techniques are proposed in the literature. We first describe the dynamic characterization techniques such as ultrasounds, Brillouin scattering, dynamic mechanical analysis (DMA) to measure the elastic properties: Young's modulus (E) , shear modulus (G), poisson ratio (υ) but also attenuation and internal friction. Thanks to "static" techniques such as three-point bending, uniaxial compression, compression we also access to the elastic modulus (E) and to the rupture strength (σ). The experimental results show that the value of the elastic and fracture moduli measured is several orders of magnitude lower than that of a material without porosity. With regard to the brittleness characteristics, Weibull's analysis is used to show the statistical nature of the fracture resistance. We also present the SENB (single edge notched beam technique) technique to characterize toughness (K1C) and the stress corrosion mechanisms, which are studied in ambient conditions and temperature by the double-cleavage drilled compression experiment (DCDC). In the last part of the paper, we show how, during the isostatic compression test, aerogels behave like plastic materials.The data allow calculating the bulk modulus (K), the amplitude of the plastic deformation and the yield strength (σel), which is the boundary between the elastic and plastic domains. These different techniques allow understanding which parameters influence the overall mechanical behavior of aerogels, such as pore volume, but also pore size, internal connectivity and silanol bounds content. It is shown that pore size plays a very important role; pores can be considered as flaws in the terms of fracture mechanics.

Silica–wollastonite xerogel composites (xerocomposites) with different wollastonite filler content were obtained after classical drying of silica–wollastonite gels. Two different silica precursors were used, TEOS and colloidal LUDOX, for composites named TW and LW, respectively. We utilized SAXS experiments, N2 adsorption–desorption, and SEM techniques to determine the textural and structural properties of these porous materials. For both the TW and LW composites, it was shown that a macroporosity and a mesoporosity coexist. We argue that the proportion of macroporosity directly depends on the proportion of wollastonite fillers in the composite. We propose a unique two-stage drying mechanism to explain the formation of macropores. We additionally found that the surface of wollastonite fillers was covered by a dense multilayer packing of silica colloids in LUDOX LW xerocomposites. We believe that these surface-modified wollastonite fillers could improve the carbonation kinetics of wollastonite when used as a precursor for aqueous mineral carbonation, a promising route for safe and durable carbon sequestration.

Silica-wollastonite xerogel composites (xerocomposites) with different wollastonite filler content were obtained after classical drying of silica-wollastonite gels. Two different silica precursors were used, TEOS and colloidal LUDOX, for composites named TW and LW, respectively. We utilized SAXS experiments, N2 adsorption-desorption, and SEM techniques to determine the textural and structural properties of these porous materials. For both the TW and LW composites, it was shown that a macroporosity and a mesoporosity coexist. We argue that the proportion of macroporosity directly depends on the proportion of wollastonite fillers in the composite. We propose a unique two-stage drying mechanism to explain the formation of macropores. We additionally found that the surface of wollastonite fillers was covered by a dense multilayer packing of silica colloids in LUDOX LW xerocomposites. We believe that these surface-modified wollastonite fillers could improve the carbonation kinetics of wollastonite when used as a precursor for aqueous mineral carbonation, a promising route for safe and durable carbon sequestration.

We modelled deep indentation in brittle materials via a tensorial approach in three dimensions. Experimentally, we performed deep indentation in base catalyzed aerogels. When deep indentation is performed in these materials, it appears a Hertzian cone crack for both experimental and numerical results. The cone angle (angle between the surface and the boundaries of the Hertzian cone) depends on the material in which indentation is performed. The Young moduli of the materials has no effect on these angles. The tendency is that materials with increasing Poisson ratios have a decreasing value of the Hertzian cone angle.